Thanks for the picture! I would be happy to help you Yes, you are correct in assuming you will only need one set of the Swing Out Extension Brackets for HappiJac Truck Camper Jack Systems Item # LC182496. These come in pairs and you will not need them for the rear set of jacks. Those are compatible with your HappiJack Electric Jacks. view full answer...
The Draw-Tite Max-Frame Trailer Hitch Receiver # 76050 is made out the same steel as the Curt Hitch.
The Draw-Tite Hitch has an easy bolt-on installation with no welding required. The hitch just bolts on differently. The Drawtite hitch also has a concealed cross tube that gives it a more clean factory look after the hitch is installed. The trailer hitch has a black powder coat finish that covers a e-coat base that offers a superior rust protection.
The hitch has a maximum tongue weight... view full answer...
I checked the instructions and you are going to need to install the plastic pieces on the Dodge ProMaster Van Adapter for Thule HideAway Awning # TH301650.
I can assure you this kit is the correct kit for your 2021 Ram ProMaster 3500 as it is made for 2014 and up Ram ProMaster's with a high roof and a 159" wheelbase. view full answer...
It sounds like you're looking for the Ceiling Garnish for MaxxAir Maxxfan RV Roof Vent # MA54FR, and will fit a standard vent opening of 14" x 14". view full answer...
If you're wanting to use the Curt # C51180, the only other part you'd need is the 4-pole upgrade kit, part # ETBC7L. The kit includes the 4-pole to 7-way adapter as well as the necessary wire, hardware and circuit breaker to run the power supply circuit to the positive battery terminal. There is a wire for reverse lamps on the adapter, but you can leave it disconnected if you wish.
The Echo would be a good choice for your trailer, and would be much simpler and faster to install than a... view full answer...
The Tekonsha OEM Replacement Vehicle Wiring Harness w Brake Controller Adapter # 22112 will give you the 7-way connector and all the wiring you will need to install a Tekonsha Prodigy P3 Trailer Brake Controller # 90195 on your 2022 Ram ProMaster 3500. view full answer...
The etrailer Trailer Hitch Receiver # e99AR is confirmed for your 2019 Ram ProMaster 3500. There is not a class 4 or class 5 hitch available for your vehicle.
The etrailer hitch has a bolt-on installation with no welding required. It has a matte black powder coat finish that is over a protective base coat that offers a superior rust resistance. The etrailer hitch has an extra coating of rust resistant paint that will help it survive the elements better then the other hitches confirmed... view full answer...
For your trailer, I recommend the Dexter Trailer Idler Axle w/ Hubs # 20545I-EZ-72-10.
This axle has a maximum weight capacity of 2,200-lbs, measures 72" from hub face to hub face, and 58" from spring center to spring center. This will fits wheel 8"-12" wheels, and includes pre-greased idler hubs, with bearings, races, and seals.
However, the spring center to center are a little off and you will need to weld on new hangers.
I have included a couple videos for you to check out as well. view full answer...
We can definitely accomplish your goal, which is to have a wiring connector on your 2022 Ram ProMaster 3500 with both a 7-way and a 4-way. While you cannot use the # C58DR without connecting it, the 7-way adapter you'll use actually has a plug on the side that allows a 4-way connection, as you can see in the photo I added.
Since your '22 ProMaster does not have the tow package, the first thing you'll need to do is install a 4-way. And while the Curt T-Connector # C58DR will fit, I highly... view full answer...
Go To Results